Red Hat GLOBAL FILE SYSTEM 5.0 Manuale Utente

Navigare online o scaricare Manuale Utente per Server Red Hat GLOBAL FILE SYSTEM 5.0. Parallels Server Bare Metal 5.0 Manuale Utente

  • Scaricare
  • Aggiungi ai miei manuali
  • Stampa
  • Pagina
    / 28
  • Indice
  • SEGNALIBRI
  • Valutato. / 5. Basato su recensioni clienti
Vedere la pagina 0
Copyright © 1999-2011 Parallels Holdings, Ltd. and its affiliates. All rights reserved.
Parallels Server Bare Metal
5.0
Deploying Clusters in Parallels-Based Systems
Vedere la pagina 0
1 2 3 4 5 6 ... 27 28

Sommario

Pagina 1 - Parallels Server Bare Metal

Copyright © 1999-2011 Parallels Holdings, Ltd. and its affiliates. All rights reserved. Parallels Server Bare Metal 5.0 Deploying Cl

Pagina 2

10 Deploying a Failover Cluster Configuring Shared Storage for Failover Clusters Once you install Parallels Server Bare Metal 5.0, you need to confi

Pagina 3 - Contents

11 Deploying a Failover Cluster Configuring Partitions on LUNs Now that you have created all the necessary partitions, perform the following operati

Pagina 4 - Introduction

12 Deploying a Failover Cluster Configuring iSCSI Data Storages If you plan to use iSCSI as a data storage, do the following: Note: Consider using G

Pagina 5 - C HAPTER 2

13 Deploying a Failover Cluster where • username and password in the node.session.auth lines denote the CHAP username and password for the initiato

Pagina 6

14 Deploying a Failover Cluster Creating and Configuring a Failover Cluster Before you start creating and configuring the failover cluster, perform

Pagina 7 - Setting Up Cluster Hardware

15 Deploying a Failover Cluster 2 Set fence devices for the cluster. The example below uses the apc network power switch as the fencing device: # c

Pagina 8

16 Deploying a Failover Cluster # ccs_tool ppscr /etc/init.d/pvapp b IP address. An IP address is required for each pair of vz and parallels-server

Pagina 9 - Deploying a Failover Cluster

17 Deploying a Failover Cluster Configuring the Cluster Once you create the cluster and set up Parallels Virtual Automation, configure the cluster a

Pagina 10 - Creating Partitions on LUNs

Data sharing clusters are server farms that share storage devices on a storage area network (SAN) and share data on those storage devices. In a data

Pagina 11

19 Deploying a Data Sharing Cluster Cluster Configuration Options A typical data sharing cluster must meet the following requirements: • The cluste

Pagina 12 - Setting up authentication

Parallels Holdings, Ltd. c/o Parallels International GMbH. Parallels International GmbH Vordergasse 49 CH8200 Schaffhausen Switzerland Tel: + 41 52632

Pagina 13

20 Deploying a Data Sharing Cluster Configuring Shared Storages on NFS The process of configuring a data shared storage located on an NFS volume inc

Pagina 14 - Creating the Cluster

21 Deploying a Data Sharing Cluster # chkconfig rpcbind on # chkconfig nfslock on # chkconfig nfs on # chkconfig netfs on 3 Enable the cluster mode

Pagina 15

22 Deploying a Data Sharing Cluster Configuring Shared Storages on GFS Setting up a shared data storage located on a partition formatted with GFS v2

Pagina 16

23 Deploying a Data Sharing Cluster As a result of the aforementioned command, a new GFS file system with the gfs2 name for the psbmCluster cluster

Pagina 17 - Configuring the Cluster

24 Deploying a Data Sharing Cluster Creating and Configuring a Data Sharing Cluster Before creating and configuring a data sharing cluster, enable t

Pagina 18 - C HAPTER 4

25 Deploying a Data Sharing Cluster • apc port=1 is the name of the fencing device (APC) and the unique port ID of the APC switch power for the psb

Pagina 19 - Clusters

26 Deploying a Data Sharing Cluster This command creates the clustered service pservice1; enables its autostart (-a 1); configures the service to ru

Pagina 20

Once you create the cluster, you can start managing it using the clusvcadm and clustat utilities. Below are some examples of using these utilities:

Pagina 21

Index C Cluster Configuration Options - 9, 19 Configuring iSCSI Data Storages - 12 Configuring Shared Storage for Failover Clusters - 10 Configuring

Pagina 22 - In this example:

Contents Introduction ... 4 Preparing to

Pagina 23

In Parallels Server Bare Metal 5.0, you can use Red Hat Cluster Suite (RHCS) to deploy the following types of clusters from Parallels servers: • Fa

Pagina 24

This section provides general information on clusters you can deploy in Parallels systems and outlines the operations you need to perform to prepare

Pagina 25

6 Preparing to Create a Cluster Understanding the Cluster Configuration The implementation of failover and data sharing clusters in Parallels system

Pagina 26 - service:

7 Preparing to Create a Cluster Setting Up Cluster Hardware In the first step, you need to set up hardware for your cluster. This procedure includes

Pagina 27 - Managing Clusters

8 Preparing to Create a Cluster Installing Parallels Server Bare Metal 5.0 After you set up cluster hardware and install clustering software, you ca

Pagina 28

This section familiarizes you with the way to use the Red Hat Cluster Suite (RHCS) software for creating failover clusters from Parallels servers. I

Commenti su questo manuale

Nessun commento